All-In-One Cold Plunge

• Exterior (LWH): 2000mm x 850mm x 920mm
• Tub Length: 1200mm
• Tub Depth: 700mm
• Tub Width: 741mm
• Tub Volume: 550 Litres

The All-In-One Cold Plunge comes with a 20-micron filter that efficiently captures particles and contaminants from the water. This filter is designed to be easily changeable.

Our chiller has a high water flow output to keep the water extremely well circulated and filtered. If the filter gets full and it isn’t changed, you will notice that the water flow rate (litres of water circulated through the chiller per minute) shown on the control panel, slows down. This affects the performance of the chiller considerably. The bubbles (ozone) decrease, which in turn, decreases the amount of filtration and ozone flowing into the tub and more.

We recommend changing the filter at least every month based on daily use by one person. Or as often as weekly or every few days in a commercial setting.

However there are many variables at play that may contribute to the filter needing to be changed more regularly. Including how clean the water is when filling tub initially or the amount of particles entering the water when being used.

We have replacement filters available for the All-In-One Cold Plunge in packs of one, three or six. You can find them in this link.

Step-by-Step Guide to Changing your All-in-One Cold Plunge Filter

1. Turn Off and Unplug the Chiller:

• Switch off the chiller.
• Unplug it from the power source for safety.

2. Remove the End Panel:

• Locate and remove the panel at the end of the ice bath to access the chiller unit.

3. Turn both of the Water Stop Valves OFF

• Locate the tap for the Water Stop Valve on the outlet and inlet connection on the chiller unit.
• Turn the taps OFF. When tap handle is perpendicular with pipes it is off.

4. Locate the 20 Micron Water Filter:

• The 20 micron water filter is situated on the right side of the chiller unit.

5. Detach the Filter Housing:

• Use the supplied wrench to loosen the filter housing.
• Turn the wrench to the left (towards your body) to undo the housing.
• Unscrew housing until you can remove the housing completely to take out the old filter. 

6. Remove the Old 20 Micron Filter:

• Take out the filter and empty any water from inside the housing.

7. Clean the Housing:

• Thoroughly clean the inside of the housing using hydrogen peroxide or mild dish soap.
• Ensure you rinse out any cleaner completely from the housing.

8. Insert the New 20 Micron Filter:

• Place a new filter into the housing.
• Screw the housing back onto the cap on the chiller unit securely.

9. Clean the Permanent Metal Filter

• Located on the inlet hose to the chiller is a small permanent metal filter.
• Unscrew the housing.
• Remove the metal filter and thoroughly clean the inside of the housing and metal filter using hydrogen peroxide or mild dish soap.
• Insert the metal filter back into the housing and screw securely onto the cap on the inlet hose.

10. Turn the water stop valve taps back ON.

11. Power On the Chiller:

• Plug the chiller back into the power source.
• Turn the chiller on and check for proper operation. The chiller will clear any air bubbles and then begin circulating water.

Follow these steps to ensure a smooth and efficient filter change for your all-in-one cold plunge.

The Ozone Generator integrated into The All-In-One Cold Plunge further enhances the water quality. Ozone is a powerful natural oxidiser that helps eliminate algae, bacteria, viruses, and other microorganisms from the water. It reduces the need for chemical disinfection while maintaining water purity.

• Wear appropriate swimwear.
• Shower before entering the Cold Plunge.
• Avoid introducing lotions, oils, or the like into the Plunge Tub.
• Place the Insulated Tub Lid back on after each use to minimise dust and particles getting in the water.
• Add a Spa Disc/Sponge to the water. This eliminates surface oils and reduces scum line formation. The disc/sponge attracts oils, removing them from the water.
• If your tub is going to be used heavily by many people we recommend using an O2 Shock treatment in the water when needed. O2 Shock is an easy to use, fast-acting, safe but powerful (chlorine free) oxidising agent that quickly eliminates algae, bacteria and organic contaminants such as sweat and body oils that can make your water cloudy and uninviting.

We provide a two man delivery service directly to your home or business. Our delivery team will contact you to arrange delivery at a time that best suits.